Yoke Rebuild

This page is a documentation of a complete teardown, refurbish (paint & lube), and rebuild of an Atari Star Wars type yoke control.

Replacement parts now available at RAM Controls: http://www.ram-controls.com/order-sw.html (I will use most of their parts nomenclature.)

Also, a source for METAL replacement gears is W.M. BERG: http://www.wmberg.com/

NOTE: I have not tested these gears for compatibility and some (specifically the 60 tooth gears) would at least require drilling out the bore to accommodate the diameter of the steering/handle shafts, but the following are my best estimates as to replacement gear part numbers:

14 tooth Y-axis pot gear: P24A66-14 (in ANODIZED ALUMINUM) or P24PH28-14 (in STAINLESS STEEL)

28 tooth X-axis pot gear: P24PH28-28 (in STAINLESS STEEL)

60 tooth X/Y-axis shaft gear: P24B34X-60 (BRASS or BRONZE - it's unclear) or P24A68-60, P24A67-60, P24A66-60 (in ANODIZED ALUMINUM) or P24S35-60, P24S34X-60 (in STAINLESS STEEL)

... but do your homework and make sure these will work before ordering.

The Guide

NOTE: Wires, potentiometers (pots), and microswitches may differ from original.

SAVE EVERYTHING YOU REMOVE FROM THE YOKE (EVEN IF REPLACING) UNTIL IT IS REBUILT

Step 1: Loosen X-axis pot retainer nut with 1/2" wrench. Remove shoulder bolt from X-axis pot 28-tooth spur gear hub using allen wrench. Remove spur gear from pot.

Step 2: Remove X-axis pot retainer nut and star washer. Remove Pot.

Step 3: Remove shoulder bolt from X-axis shaft 60-tooth spur gear hub using allen wrench. Remove spur gear from shaft.

Step 4: Remove C-clip using flathead screwdriver.

Step 5: Remove shaft washer.

Step 6: Loosen anchor pin using 5/16" wrench or socket. Hold anchor nut using another 5/16" wrench

Step 7: Remove anchor pin and nut. Rotate steering assembly frame while doing so to relieve spring tension on pin and nut.

Step 8: Slide torsion springs and steering assembly frame off the steering shaft.

Step 9: Remove bump stops (if they exist) from metal pins on steering assembly frame and handle assembly frame (4 total).

Step 10: Remove white plastic bushing from steering shaft.

Step 11: Remove shoulder bolt from handle assembly frame steering shaft hub using allen wrench. 3 total (one on underside).

Step 12: Remove steering shaft from handle assembly frame.

Step 13: Loosen Y-axis pot retainer nut with 1/2" wrench. Loosen set screw from Y-axis pot 14-tooth spur gear hub using allen wrench.

Step 14: Remove spur gear from pot. A 3/8" wrench is handy as a gear puller.

Step 15: Remove bolt from Y-axis shaft limiter pin using allen wrench. Rotate handles while doing so to relieve spring tension on pin.

Step 16: Remove outer and inner shoulder bolt from handle hub using allen wrench.

Step 17: Wonder why the handle won't come off. Wonder what that other thing is between the outer and inner shoulder bolt holes. Realize it is a pressed-in spring pin. Ponder how to get it out.

Step 18: Cut wires free from microswitches. Pull wires back through handle shaft. Remove microswitch bolts using screwdriver and remove microswitches. Use screwdriver inside handle shaft to push spring pin outwards.

Step 19: Grip spring pin with vise grips and pull. Repeat until spring pin actually comes out. At some point, you may be able to rotate it a bit while pulling.

Step 20: Marvel at the fact you have triumphed over an inanimate 4 cent piece of steel. Repeat steps 16-20 for other handle (if you want/need to - the other handle could stay on the handle shaft. Remove shoulder bolt from Y-axis shaft 60-tooth spur gear hub using allen wrench. Remove C-clips using hook pick or other tool, but be extremely cautious if prying with a screwdriver as it would be too easy to damage the plastic (but expensive to replace) gear. Slide handle shaft out of handle assembly frame and torsion springs. Remove torsion springs. Pick out gear that has been freed.

Step 21: Gently tap handle shaft bearing towards interior of handle assembly frame using hammer.

Step 22: The ball end on my screwdriver worked well to free the bearing from the handle assembly frame.

(MORE TO COME, IT'S LATE)