Difference between revisions of "LS-30 Switch Service"

From BYOAC OLD Wiki
Jump to navigation Jump to search
Line 9: Line 9:
  
 
*  
 
*  
The rotary switches on the LS-30 Sticks are built like tanks, but by now they've often seen enough use to benefit from cleaning a re-greasing. The first stick I did this on went from 10 ohm to 0.5 ohm contact resistance. So if you have a stick that doesn't doesn't seem to be working right this is worth a try.
+
The rotary switches on the LS-30 Sticks are built like tanks, but by now they've often seen enough use to benefit from cleaning and re-greasing. The first stick I cleaned went from 10 ohm to 0.5 ohm contact resistance. So if you have a stick that doesn't doesn't seem to be working right this is worth a try.
  
  
Line 16: Line 16:
 
There's a simple way to get the handles off! I don't think I would have figured this out without  this [http://forum.arcadecontrols.com/index.php?topic=13028.0 forum post.]
 
There's a simple way to get the handles off! I don't think I would have figured this out without  this [http://forum.arcadecontrols.com/index.php?topic=13028.0 forum post.]
  
Align the tips of the wire under the cap where the two little posts are and pull up to disingage the cap.<br>
+
Align the tips of the wire under the cap where the two little posts are and pull up to disengage the cap.<br>
 
[[Image:cap_removal.jpg]]
 
[[Image:cap_removal.jpg]]
  
Line 36: Line 36:
 
Once the case is open you can remove the contact carrier, circuit board and detent assembly. The circuit board is secured to the case but comes off with a little gentle prying (I said gentle). Be very careful removing the detent assembly under the circuit board as it contains several tiny parts that are easily lost (two springs, two small metal plates, and two cylindrical rollers). <br>
 
Once the case is open you can remove the contact carrier, circuit board and detent assembly. The circuit board is secured to the case but comes off with a little gentle prying (I said gentle). Be very careful removing the detent assembly under the circuit board as it contains several tiny parts that are easily lost (two springs, two small metal plates, and two cylindrical rollers). <br>
  
Here are the parts after dissasembly <br>
+
Here are the parts after disassembly <br>
 
[[Image:dirty_switch_parts.jpg]] [[Image:dirty_switch_top.jpg]]
 
[[Image:dirty_switch_parts.jpg]] [[Image:dirty_switch_top.jpg]]
  

Revision as of 02:56, 4 August 2008

Pliers.jpg
Cap removal tool.jpg


Tools Needed:

  • Snap ring pliers
  • Home-made top cap removal tool
  • Socket wrench with 10mm socket
  • regular pliers


The rotary switches on the LS-30 Sticks are built like tanks, but by now they've often seen enough use to benefit from cleaning and re-greasing. The first stick I cleaned went from 10 ohm to 0.5 ohm contact resistance. So if you have a stick that doesn't doesn't seem to be working right this is worth a try.



There's a simple way to get the handles off! I don't think I would have figured this out without this forum post.

Align the tips of the wire under the cap where the two little posts are and pull up to disengage the cap.
Cap removal.jpg

Hold the top and loosen the 10mm nut inside. Once loosened the top will slide off easily.
Top nut.jpg

Remove the snap ring (you really do need snap ring pliers for this)
Remove snap.jpg

You should be able to pull the switch assembly out of the body at this point.
LS-30 parts.jpg

The outer sleeve part of the switch assembly shaft unscrews from the base. In order to protect the shaft from marring I wrapped it in several layer of electrical tape before unscrewing it with a pair of pliers.
Switch assembly.jpg Sleeve removed.jpg

Straighten the four bent tabs on the top of the switch housing and gently work the case apart. It helps to push the tabs down from the top.
Tabs bent.jpg

Once the case is open you can remove the contact carrier, circuit board and detent assembly. The circuit board is secured to the case but comes off with a little gentle prying (I said gentle). Be very careful removing the detent assembly under the circuit board as it contains several tiny parts that are easily lost (two springs, two small metal plates, and two cylindrical rollers).

Here are the parts after disassembly
Dirty switch parts.jpg Dirty switch top.jpg

The grease had dried up and the blue upper housing had started to wear. As well, smell flecks of metal had worn of the shaft and made their way into the switch. This switch actually read fine with a multimeter, but I'd say it will live a lot longer after cleaning and re-greasing.

Here they are after cleaning. The circuit board was cleaned with alcohol and treated with Deoxit D5 contact cleaner (fantastic stuff by the way)
Clean switch parts.jpg

New grease was put on where it had been applied originally. I used Molykote EM-30L as I had some from lubricating a spinner. It's a light, plastic safe lithium grease.
Greased switch parts.jpg


If the switch wasn't working properly it may be a good idea to bend the switch contacts up a tiny bit to make better contact. It should be easy to tell if this is necessary. Once all the parts are back in the upper switch housing, just look at it from the side and make sure all three contacts are touching the board. I wouldn't bend the contacts unless it obviously needs to be done.

LS-30 assembly1.jpg LS-30 assembly2.jpg LS-30 assembly3.jpg LS-30 assembly4.jpg