Difference between revisions of "LS-30 Switch Service"

From BYOAC OLD Wiki
Jump to navigation Jump to search
 
(Disassembly)
Line 12: Line 12:
 
There's a simple way to get the handles off! I don't think I would have figured this out without  this [http://forum.arcadecontrols.com/index.php?topic=13028.0 forum post.]
 
There's a simple way to get the handles off! I don't think I would have figured this out without  this [http://forum.arcadecontrols.com/index.php?topic=13028.0 forum post.]
  
Align the tips of the wire under the cap where the two little posts are and pull up to disingage the cap.
+
Align the tips of the wire under the cap where the two little posts are and pull up to disingage the cap.<br>
 
[[Image:cap_removal.jpg]]
 
[[Image:cap_removal.jpg]]
  
Hold the top and loosen the 10mm bolt inside. Once loosened the top will slide off easily.
+
Hold the top and loosen the 10mm bolt inside. Once loosened the top will slide off easily.<br>
 
[[Image:top_nut.jpg]]
 
[[Image:top_nut.jpg]]
  
Line 21: Line 21:
 
[[Image:Remove_snap.jpg]]
 
[[Image:Remove_snap.jpg]]
  
You should be able to pull the switch assembly out of the body at this point.
+
You should be able to pull the switch assembly out of the body at this point.<br>
 
[[Image:LS-30_parts.jpg]]
 
[[Image:LS-30_parts.jpg]]
  
 
The outer sleeve part of the switch assembly shaft unscrews from the base. In order to protect the shaft from marring I wrapped it in several layer of electrical tape before unscrewing it with a pair of pliers. <br>
 
The outer sleeve part of the switch assembly shaft unscrews from the base. In order to protect the shaft from marring I wrapped it in several layer of electrical tape before unscrewing it with a pair of pliers. <br>
 
[[Image:Switch_assembly.jpg]] [[Image:sleeve_removed.jpg]]
 
[[Image:Switch_assembly.jpg]] [[Image:sleeve_removed.jpg]]
 +
 +
Straighten the four bent tabs on the top of the switch housing and gently work the case apart. It helps to push the tabs down from the top.<br>
 +
[[Image:tabs_bent.jpg]]
 +
 +
Once the case is open you can remove the contact carrier, circuit board and click mechanism (not official names). The circuit board is secured to the case but comes off with a little gentle prying (I said gentle). Be very careful removing the click assembly under the circuit board as it contains several tiny parts that are easily lost (two springs, two small metal plates, and two cylindrical rollers). <br>
 +
 +
Here are the parts after dissasembly <br>
 +
[[Image:dirty_switch_parts.jpg]] [[Image:dirty_switch_top.jpg]]
 +
 +
The grease had dried up and the blue upper housing had started to wear. As well, smell flecks of metal had worn of the shaft and made their way into the switch.
 +
 +
Here they are after cleaning. <br>
 +
[[Image:clean_switch_parts.jpg]]

Revision as of 22:20, 3 August 2008

Pliers.jpg
Cap removal tool.jpg


Tools Needed:

  • Snap ring pliers
  • Home-made top cap removal tool
  • Socket wrench with 10mm socket


Disassembly

There's a simple way to get the handles off! I don't think I would have figured this out without this forum post.

Align the tips of the wire under the cap where the two little posts are and pull up to disingage the cap.
Cap removal.jpg

Hold the top and loosen the 10mm bolt inside. Once loosened the top will slide off easily.
Top nut.jpg

Remove the snap ring (you really do need snap ring pliers for this)
Remove snap.jpg

You should be able to pull the switch assembly out of the body at this point.
LS-30 parts.jpg

The outer sleeve part of the switch assembly shaft unscrews from the base. In order to protect the shaft from marring I wrapped it in several layer of electrical tape before unscrewing it with a pair of pliers.
Switch assembly.jpg Sleeve removed.jpg

Straighten the four bent tabs on the top of the switch housing and gently work the case apart. It helps to push the tabs down from the top.
Tabs bent.jpg

Once the case is open you can remove the contact carrier, circuit board and click mechanism (not official names). The circuit board is secured to the case but comes off with a little gentle prying (I said gentle). Be very careful removing the click assembly under the circuit board as it contains several tiny parts that are easily lost (two springs, two small metal plates, and two cylindrical rollers).

Here are the parts after dissasembly
Dirty switch parts.jpg Dirty switch top.jpg

The grease had dried up and the blue upper housing had started to wear. As well, smell flecks of metal had worn of the shaft and made their way into the switch.

Here they are after cleaning.
Clean switch parts.jpg